Once, twice in month we will send You info about new products, products on sale and news from Arduino and DIY world.
Sensor.community (aka Luftdaten) compatible kit - all components to build, soldered and programmed. NodeMCU with firmware with English language. NovaFitness SD011 and Sensirion SHT31 no barometric pressure readings.
Kit with dedicated harness cable, making sturdy connection.
If kit is not available, check BME280 version, which is preferred kit setup
Small development board build on efficient ARM Cortex M0+ and LoRa radio! Build in solar and lithium battery energy management system. Arduino compatible!
Small development board build on efficient ARM Cortex M0+ and LoRa radio! Build in GPS receiver and OLED screen.
Special cable for connecting the battery to CubeCell modules.
LCD touch screen controlled by the SPI bus. Built-in SD card slot. Screen with a resolution of 480x320px.
Core of NAM 0.3 ecosystem. Central unit with PM sensor, Wi-Fi connectivity (embedded antenna) and enclosure. Kit includes BMP180 & SHT31 sensors instead of BME280. Requires soldering.
Simple module plugged directly to EXT port of NAM 0.3. This device allows for power cycling of SDS011.
Small LCD display on ST7735 driver with SPI interface. Square display 128x128 px.
Core of NAM 0.3 ecosystem. Central unit with PM sensor, Wi-Fi connectivity (embedded antenna) and enclosure. Kit includes BMP180 & SHT31 sensors instead of BME280. Requires soldering.
Това е стандартната версия, използвана в мрежата на AirBG.Info / Sensor Community. Версия с SHT31 вместо BME280
Slim plastic case for BBC micro:bit V2.
Slim plastic case for BBC micro:bit V2.
Slim plastic case for BBC micro:bit V2.
Slim plastic case for BBC micro:bit V2.
Slim plastic case for BBC micro:bit V2.
Slim plastic case for BBC micro:bit V2.
Kit to solder, includes Wemos with Polish Firmware (can be changed after configuration). Includes SHT31/BMP180 instead of BME280. Has external WiFi antenna.
Complete solution to measure PM2.5, PM10, temperature, humidity and pressure.
MemsFrontier MPM-10B optical dust sensor
Protoboard to build circuit (solder). Stripboard type but also it is compatible with breadboard layout. Transfer circuit from breadboard to soldered one on this protoboard is simple task.
Small case for PCB with sensor like SHT31 or BME280.
Motor driver module TB6612FNG
Kit to solder, includes Wemos with English Firmware (can be changed after configuration). Includes SHT31/BMP180 instead of BME280. Has external WiFi antenna.
Cable USB A/B for UNO or MEGA.
8MB PSRAM chip for Teensy 4.1
Sensor.community (aka Luftdaten) compatible kit - all components to build, soldered and programmed. NodeMCU with firmware with English language. NovaFitness SD011 and BME280.
Kit with dedicated harness cable, making sturdy connection.
USB adapter for ESP01. Switch to select between programming and UART mode.
CC1101 based module, 433 MHz
ESP01 relay module - just plug in ESP01 and You have ready to work WiFi enabled relay.
MTP40-F NDIR CO2 sensor working in range 400-5000 ppm.
Small PCB, breakout for MPM10B PM sensor
Larger version of Teensy 4.0 with tons of additional GPIO, microSD card slot and USB Host. 4x more Flash memory and 600MHz of pure power!
This is version WITHOUT Ethernet PHY.
Microswitch 12x12 with red cap.
Microswitch 12x12 with yellow cap.
Microswitch 12x12 with green cap.
Nice cable with switch. USB A on one end, wires on second end.
Simple and cheap ultrasonic range sensor. Works with 3.3V logic levels (ESP8266)
Developer board with ESP32-S and integrated OV2640 camera. With USB/Serial module.
Once, twice in month we will send You info about new products, products on sale and news from Arduino and DIY world.