Nettigo Air Monitor - 0.3.3 SHT/BMP

This is SHT/BMP version. Select it ONLY if kit versions with BME280 are not available. BMP180 used as pressure sensor is much worse than one in BME280.

This KIT requires soldering and basic manual skills. Before assembly you should know how to solder and use screwdriver. This kit includes Wemos with Polish firmware, can be changed after basic configuration. Version with English firmware is also available.

What's the deal with NAM sensor

NAM sensor is based on Sensor.Community (Luftadten) project. Thus Your sensor automatically will send data to Sensor.Community sensor network. It has better case and it is soldered on dedicated PCB. No more data loss due to faulty jumper wire. And, in our opinion most important difference: heating chamber with automatic air conditioning to keep relative humidity below 70%. Why it is so important?

This figure shows PM10 readings from two SDS011 based sensors with RH close to 100%. One is equipped with heating chamber (green line) and one is not (yellow line). Without heating and control element in RH higher than 70% You can observe condensation. With this process water and dust particles combine making more and bigger objects. Optical sensors can return readings few times higher when condensation phenomenon is present.

SHT31/BMP180

From some time there is no BME280 on market. As such we had to incorporate changes in our kits. So, instead BME280, we use two sensors. Sensirion SHT31 is precise temperature and humidity sensor. It should be mounted where BME280 was placed in older kits. Second sensor (Bosch BMP180) will measure pressure. BMP180 module should be placed inside of NAM case. Vent holes are big enough to provide equal pressure inside and outside case.

This is only difference between previous NAM 0.3.3 STD PL. When BME280 will be available again we will use it in future kits again.

Set includes:

• NAM BASE KIT:
  • 1 pcs x Wemos D1 mini Wi-Fi module (Polish firmware)
  • 1 pcs x PM Sensor NovaFitness SDS011
  • 1 pcs x Nettigo Air Monitor - PCB 0.3.3
  • 1 pcs x Polymer fuse 0.9A 60V
  • 1 pcs x TVS Diode
  • 1 pcs x Capacitor 470uF, 35V
  • 1 pcs x Long header, 6 pin, 2.54mm raster
  • 1 pcs x Short header, 6 pin, 2.54mm raster
  • 1 pcs x XH2.54-3P socket
  • 6 pcs x XH2.54-4P socket
  • 1 pcs x Barrel jack socket DC 2.1/5.5
  • 1 pcs x Terminal block, 2P, 5mm
  • 1 pcs x IDC16 THT Connector
  • 1 pcs x Enclosure Kradex Z59JpH with custom holes
  • 3 pcs x Standoff 8 mm, F/F, M3, brass
  • 10 pcs x Screw M3, 5mm
  • 10cm x Single layer technical hose 6-1.5 mm
• NAM HECA KIT:
  • 1 pcs x Nettigo Air Monitor HECA - Heating Element Control Assembly
  • 1 pcs x PTC Heating Element 70C 12V
  • 1 pcs x Cable with XH2.54 10cm 4P connector
  • 10 cm x Cable LgY 0.35 mm² red
  • 10 cm x Cable LgY 0.35 mm² black
  • 2 pcs x Reduction Sleeve PP BSP 1” outside - BSP1/2” inside
  • 1 pcs x Coupling PP BSP 1” outside - BSP 1” outside
  • 1 pcs x Hose connector PP 16 mm - BSP 1/2” outside
  • 1 pcs x Suction basket (filter) BSP 1/2”
• NAM SHT/BMP KIT:
  • 1 pcs x Sensirion SHT31 sensor
  • 1 pcx x jumper wire to change SHT31 I2C address (2 cm)
  • 1 pcs x Bosch BMP180 sensor
  • 1 pcs x heat shrink tube to protect BMP180 (2-2.5 cm)
  • 2 pcs x Cable with XH 2.54 4P connector
  • 1pcs x Thread reduction M16 - M20
  • 1pcs x Plastic M20 cap
  • 1pcs x Flat nut M16 x 1.5 mm
• D-Link wall power supply 5V 1.2A DC 2.1/5.5 mm

NAM 0.3 STD (embedded WiFi antenna)

NAM 0.3 - PRO (external WiFi antena)

NAM 0.3 - parts and accessories:

Power accessories for NAM