Nettigo Air Monitor (KIT BME 0.3.3 PRO language PL) - Build your own smog sensor!

This KIT requires soldering and basic manual skills. Before assembly you should know how to solder and use screwdriver.

What's the deal with NAM sensor

NAM sensor is based on Sensor.Community (Luftadten) project. Thus Your sensor automatically will send data to Sensor.Community sensor network. It has better case and it is soldered on dedicated PCB. No more data loss due to faulty jumper wire. And, in our opinion most important difference: heating chamber with automatic air conditioning to keep relative humidity below 70%. Why it is so important?

This figure shows PM10 readings from two SDS011 based sensors with RH close to 100%. One is equipped with heating chamber (green line) and one is not (yellow line). Without heating and control element in RH higher than 70% You can observe condensation. With this process water and dust particles combine making more and bigger objects. Optical sensors can return readings few times higher when condensation phenomenon is present.

Wersja PRO

This is version NAM 0.3.3 PRO - it has Wemos D1 mini PRO. It has connector to external antenna (pigtail and antenna are included). With external antenna module has better WiFi range - in other words can be placed in bigger distance from WiFi Access Point (compared to version NAM 0.3.3 STD) and will work better in environments with many WiFi networks.

Wemos D1 mini Pro has internal ceramic antenna, which is enabled by default. To activate external antenna You have to solder SMD jumper. This a bit harder task than soldering THT elements (all other components in NAM are THT kind). You can check with soldering instuctions what You have to do, to enable external antenna.

There is always other option - buy NAM 0.3.3 PRO already soldered.

Set includes:

• NAM BASE KIT:
  • 1 pcs x Wemos D1 mini PRO with firmware NAMF PL
  • 1 pcs x pigtail SMA, 15 cm
  • 1 pcs x antenna 2.4 GHz
  • 1 pcs x PM Sensor NovaFitness SDS011
  • 1 pcs x Nettigo Air Monitor - PCB 0.3.3
  • 1 pcs x Polymer fuse 0.9A 60V
  • 1 pcs x TVS Diode
  • 1 pcs x Capacitor 470uF, 35V
  • 1 pcs x Long header, 6 pin, 2.54mm raster
  • 1 pcs x Short header, 6 pin, 2.54mm raster
  • 1 pcs x XH2.54-3P socket
  • 6 pcs x XH2.54-4P socket
  • 1 pcs x Barrel jack socket DC 2.1/5.5
  • 1 pcs x Terminal block, 2P, 5mm
  • 1 pcs x IDC16 THT Connector
  • 1 pcs x Enclosure Kradex Z59JpH with custom holes
  • 3 pcs x Standoff 8 mm, F/F, M3, brass
  • 10 pcs x Screw M3, 5mm
  • 10cm x Single layer technical hose 6-1.5 mm
• NAM HECA KIT:
  • 1 pcs x Nettigo Air Monitor HECA - Heating Element Control Assembly
  • 1 pcs x PTC Heating Element 70C 12V
  • 1 pcs x Cable with XH2.54 10cm 4P connector
  • 10 cm x Cable LgY 0.35 mm² red
  • 10 cm x Cable LgY 0.35 mm² black
  • 2 pcs x Reduction Sleeve PP BSP 1” outside - BSP1/2” inside
  • 1 pcs x Coupling PP BSP 1” outside - BSP 1” outside
  • 1 pcs x Hose connector PP 16 mm - BSP 1/2” outside
  • 1 pcs x Suction basket (filter) BSP 1/2”
• NAM BME280 KIT:
  • 1 pcs x Bosch BME280 sensor
  • 1 pcs x Cable with XH 2.54 4P connector
  • 1pcs x Thread reduction M16 - M20
  • 1pcs x Plastic M20 cap
  • 1pcs x Flat nut M16 x 1.5 mm
• D-Link wall power supply 5V 1.2A DC 2.1/5.5 mm

Links:

• All documentation in docs.nettigo.pl
  • Soldering of NAM BASE KIT
  • Soldering of HECA KIT
  • Soldering of BME280

NAM 0.3 STD (embedded WiFi antenna)

NAM 0.3 - PRO (external WiFi antena)

NAM 0.3 - parts and accessories:

Power accessories for NAM